Installing USB Drivers for the TRAX Apollyon
Note that installing and using the USB drivers for the TRAX Apollyon is only supported for the Windows XP or Vista operating systems. It is not
supported for Windows 98, ME or 2000.
The first time you are downloading the TRAX Apollyon to a computer using the USB port, you will need to install the drivers for it. There are two drivers
that will be installed, one right after the other. These drivers are available on this web site, on the installation CD for the TRAXPro software, and as part
of the Windows Update feature available from Microsoft using an Internet connection.
To install the drivers, first connect a USB cable to your computer and then to the USB Download port of the Apollyon.
supported for Windows 98, ME or 2000.
The first time you are downloading the TRAX Apollyon to a computer using the USB port, you will need to install the drivers for it. There are two drivers
that will be installed, one right after the other. These drivers are available on this web site, on the installation CD for the TRAXPro software, and as part
of the Windows Update feature available from Microsoft using an Internet connection.
To install the drivers, first connect a USB cable to your computer and then to the USB Download port of the Apollyon.
The Windows 'Found New Hardware' message will pop up,
referencing USB Serial Converter, then the Found New Hardware
Wizard will appear.
One of the features of Windows XP and Vista is to use your
Internet connection to search the Windows Update web site for
any available drivers for USB devices you connect to your
computer, like the TRAX Apollyon. If you have not used this
feature before, you'll first see a screen like the one shown here
when you first connect the Apollyon.
The drivers for the Apollyon are available through this feature, so
if you'd like to allow the wizard to connect to the Internet, select
one of the first two options and click Next.
referencing USB Serial Converter, then the Found New Hardware
Wizard will appear.
One of the features of Windows XP and Vista is to use your
Internet connection to search the Windows Update web site for
any available drivers for USB devices you connect to your
computer, like the TRAX Apollyon. If you have not used this
feature before, you'll first see a screen like the one shown here
when you first connect the Apollyon.
The drivers for the Apollyon are available through this feature, so
if you'd like to allow the wizard to connect to the Internet, select
one of the first two options and click Next.
After you click Next (or if you have previously instructed Windows
to always check the Windows Update web site for drivers), you'll
see the screen shown here.
to always check the Windows Update web site for drivers), you'll
see the screen shown here.
This screen is used to tell Windows where to look for the drivers
it needs. We recommend using the first selection, Install the
Software Automatically.
Note that whenever possible we recommend you use the
drivers available through the Windows Update web site as this
is the easiest method for loading the drivers and is done
automatically during the Found New Hardware. However, if you
are not able to use the Windows Update web site, the drivers
are also available on the Downloads section of the JAMAR web
site and TRAXPro installation CDs for versions later than 2.1.3.
If you are downloading the drivers from the JAMAR web site, be
sure to follow the directions listed there. If you would like to use
the drivers on the TRAXPro CD, insert the CD into your drive.
it needs. We recommend using the first selection, Install the
Software Automatically.
Note that whenever possible we recommend you use the
drivers available through the Windows Update web site as this
is the easiest method for loading the drivers and is done
automatically during the Found New Hardware. However, if you
are not able to use the Windows Update web site, the drivers
are also available on the Downloads section of the JAMAR web
site and TRAXPro installation CDs for versions later than 2.1.3.
If you are downloading the drivers from the JAMAR web site, be
sure to follow the directions listed there. If you would like to use
the drivers on the TRAXPro CD, insert the CD into your drive.
IMPORTANT: When connecting the USB cable to
your Apollyon, be sure to plug into the USB
Download Port (not the USB Memory Port) as
shown below. The USB Memory Port should only be
used for USB Flash Drives. Also be sure that no
USB Flash Drive is plugged into the USB Memory
Port while you are trying to use the Download Port.
your Apollyon, be sure to plug into the USB
Download Port (not the USB Memory Port) as
shown below. The USB Memory Port should only be
used for USB Flash Drives. Also be sure that no
USB Flash Drive is plugged into the USB Memory
Port while you are trying to use the Download Port.
You are here: Home > Downloads > USB Driver Downloads > Apollyon USB Drivers > Installing USB Drivers
 | |  | |  | |  | |  | |  | |  |
| Making Data Collection Easier |
